Specialty Roofing Products
Filter Products By
  • Roofing Systems
  • Filter By
Jump To
Expand-O-Flash® Style PVC EJ/WC with reinforced PVC cover to weld the joint assembly to the PVC membrane.

Expand-O-Flash expansion joint covers are flexible, weather-proof
exterior covers for expansion joint openings and are an effective, flexible
closure for a wide variety of standard and special applications.

Bellows: Widths: 4" - 12" (10.16 cm - 30.48 cm) Standard
                (Other sizes are available, contact JM for more information.)
                Membrane Cover
                    JM PVC
                    Thicknesses: 0.060" (1.52 mm)
                    Width: 8" up to 75" (20.32 cm up to 1.91 m) (Depending on flashing and welding to the membrane requirements.)
                    Colors: White; Grey; Grey ES; Sandstone and Sandstone ES
                Closed Cell Support Foam
                    Thickness varies from 0.375" to 0.75" (9.53 mm to 19.1 mm) depending on bellows width.

Nail Strip: Rigid PVC
                    Width: 1.375" (3.49 cm)
                    Factory fabricated transitions are available.

Expansion-JC-PVC-EJWC-700X467
Available Documents

Elastomeric bellows supported by a closed-cell foam backer for installation on wood curbs.

Features and Components: Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications. Each Expand-O-Flash cover is a combination of a flexible rubber membrane, supported by a closed cell foam to form flexible bellows, with two metal flanges, adhesively and mechanically combined to the bellows by a patented bifurcation process. As expansion joints move, the greatest stress occurs in the cover at the point where expansion joints intersect, cross or change directions. Factory-fabricated intersections are designed for maximum flexibility and are produced using special fabrication techniques to ensure watertight, clean seam lines. Close factory tolerance and quality control assures high yield performance.

Use: Designed to manage the movement of commercial and industrial building roof systems: thermal, settlement, new and existing junctions, differing roof deck materials or direction and seismic movement. Compatible with all roof membranes.

Advantages:

  • Accommodates multidirectional movement
  • Non-reinforced bellows for both geometric and elastomeric movement
  • Designed in a variety of styles for application requirements
  • Labor saving factory crafted intersections to fit most needs or custom designed for special needs
ExpansionJC-Curb2Curb-CF-700X799

installation guides

CF & CF/EJ Installation Instructions

 

Available Documents

Elastomeric membrane bellows supported by a closed cell foam backer.

Features and Components: Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications. Each Expand-O-Flash cover is a combination of a flexible rubber membrane, supported by a closed cell foam to form flexible bellows, with two metal flanges, adhesively and mechanically combined to the bellows by a patented bifurcation process. As expansion joints move, the greatest stress occurs in the cover at the point where expansion joints intersect, cross or change directions. Factory-fabricated intersections are designed for maximum flexibility and are produced using special fabrication techniques to ensure watertight, clean seam lines. Close factory tolerance and quality control assures high yield performance.

Use: Designed to manage the movement of commercial and industrial building roof systems: thermal, settlement, new and existing junctions, differing roof deck materials or direction and seismic movement. Compatible with all roof membranes.

Advantages:

  • Accommodates multidirectional movement
  • Non-reinforced bellows for both geometric and elastomeric movement
  • Designed in a variety of styles for application requirements
  • Labor saving factory crafted intersections to fit most needs or custom designed for special needs
ExpansionJC-Curb2Wall-CF-EJ-700X1057

installation guides

CF & CF/EJ Installation Instructions

 

Available Documents

Elastomeric membrane bellows for installation on roof-to-roof conditions.

Features and Components: Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications. Each Expand-O-Flash cover is a combination of a flexible rubber membrane, supported by a closed cell foam to form flexible bellows, with two metal flanges, adhesively and mechanically combined to the bellows by a patented bifurcation process. As expansion joints move, the greatest stress occurs in the cover at the point where expansion joints intersect, cross or change directions. Factory-fabricated intersections are designed for maximum flexibility and are produced using special fabrication techniques to ensure watertight, clean seam lines. Close factory tolerance and quality control assures high yield performance.

Use: Designed to manage the movement of commercial and industrial building roof systems: thermal, settlement, new and existing junctions, differing roof deck materials or direction and seismic movement. Compatible with all roof membranes.

Advantages:

  • Accommodates multidirectional movement
  • Non-reinforced bellows for both geometric and elastomeric movement
  • Designed in a variety of styles for application requirements
  • Labor saving factory crafted intersections to fit most needs or custom designed for special needs
ExpansionJC-Cant2Cant-EJ-700X464

Installation guides

EJ Installation Instructions

Available Documents

Elastomeric membrane bellows for installation on roof-to-wall installations.

Features and Components: Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications. Each Expand-O-Flash cover is a combination of a flexible rubber membrane, supported by a closed cell foam to form flexible bellows, with two metal flanges, adhesively and mechanically combined to the bellows by a patented bifurcation process. As expansion joints move, the greatest stress occurs in the cover at the point where expansion joints intersect, cross or change directions. Factory-fabricated intersections are designed for maximum flexibility and are produced using special fabrication techniques to ensure watertight, clean seam lines. Close factory tolerance and quality control assures high yield performance.

Use: Designed to manage the movement of commercial and industrial building roof systems: thermal, settlement, new and existing junctions, differing roof deck materials or direction and seismic movement. Compatible with all roof membranes.

Advantages:

  • Accommodates multidirectional movement
  • Non-reinforced bellows for both geometric and elastomeric movement
  • Designed in a variety of styles for application requirements
  • Labor saving factory crafted intersections to fit most needs or custom designed for special needs
ExpansionJC-Cant2Wall-EJ-700X795

installation guides

EJ Installation Instructions

 

Available Documents

Elastomeric or PVC membrane supported by a closed-cell foam backer.

Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications.

Bellows:
    Widths: 4" - 12" (10.16 cm - 30.48 cm) Standard
    (special up to 54" [1.37 m] wide)

    Membrane Covers:
        EPDM
        Thicknesses: 0.060" (1.52 mm)
        Width: 12" up to 55" (30.48 cm up to 1.4 m)
        Colors: Black or White* - premium priced and available upon request.

        Neoprene*
        Thickness: 0.060" (1.52 mm)
        Width: 12" up to 55" (30.48 cm up to 1.4 m)
         Color: Black


        JM PVC (See Expand-O-Flash PVC EJ/WC data sheet)
        Thicknesses: 0.060" (1.52 mm)
        Width: 8" up to 75" (20.32 cm up to 1.91 m) (Depending on flashing and welding to the membrane requirements.)
        Colors: White; Grey; Grey ES; Sandstone and Sandstone ES

    Closed Cell Support Foam:
        Thickness varies from 0.375" - 0.75" (9.53 mm to 19.1 mm) depending on bellows width.

Nail Strip:
        Neoprene coated nylon and galvanized steel
        Width: 1.375" (3.49 cm)

Termination Bar:
        Aluminum
        Width: 1" (2.54 cm)

Styles:
    RR = Curb to Curb mounted
    RW = Curb-to-Wall mounted
    INS = Insulated available in all styles

Factory fabricated transitions are available.

ExpansionJC-Curb2Curb-EJWC-700X700
Available Documents

Elastomeric or PVC membrane for installation on any width curb.

Expand-O-Flash expansion joint covers are flexible, weather-proof exterior covers for expansion joint openings and are an effective, flexible closure for a wide variety of standard and special applications.

Bellows:
        Widths: 4" - 12" (10.16 cm - 30.48 cm) Standard
        (special up to 54" [1.37 m] wide)

Membrane Covers:
    EPDM
    Thicknesses: 0.060" (1.52 mm)
    Width: 12" up to 55" (30.48 cm up to 1.4 m)
    Colors: Black or White* - premium priced and available upon request.

    Neoprene*
    Thickness: 0.060" (1.52 mm)
    Width: 12" up to 55" (30.48 cm up to 1.4 m)
    Color: Black
    JM PVC (See Expand-O-Flash PVC EJ/WC data sheet)
    Thicknesses: 0.060" (1.52 mm)
    Width: 8" up to 75" (20.32 cm up to 1.91 m) (Depending on flashing and welding to the membrane requirements.)
    Colors: White; Grey; Grey ES; Sandstone and Sandstone ES

Closed Cell Support Foam:
    Thickness varies from 0.375" - 0.75" (9.53 mm to 19.1 mm) depending on bellows width.

Nail Strip:
    Neoprene coated nylon and galvanized steel
    Width: 1.375" (3.49 cm)

Termination Bar:
    Aluminum
    Width: 1" (2.54 cm)

Styles:
    RR = Curb to Curb mounted
    RW = Curb-to-Wall mounted
    INS = Insulated available in all styles

Factory fabricated transitions are available.

ExpansionJC-Curb2Wall-EJWC-700X700
Available Documents

Moisture/vapor venting unit designed to release and prevent the re-entry of moisture-laden air.

Designed for use in bituminous roofing systems, the FP-10 One Way Roof Vent is a solar operated, moisture/vapor venting unit designed to release and prevent the re-entry of moisture-laden air in new or existing lightweight fill decks and most low-slope industrial/commercial roofing systems.

One-Piece Flange and Body: Polyethylene Body: 4.5" (11.43 cm) base diameter, 6" (15.24 cm) height / Flange: 10" (25.4 cm) diameter

Weatherproof Cap: Polyethylene

Valve: Silicone rubber

Color: Black

SRP_DV_FP-10OneWayVent
Available Documents

One-piece spun aluminum body, TPO-coated flange and depressed sump area.

Designed for use in single ply TPO roof systems to replace existing drains in re-roofing applications. The one-piece spun aluminum body has a TPO-coated flange for direct hot air welding of TPO roof membranes. The drain flange has a depressed sump area for improved flow and to facilitate drainage.

One-piece Seamless Body: 0.125" (3 mm) spun aluminum with 12" (30.48 cm) drain stem length, and an extra large 17.5" (44.45 cm) diameter TPO-coated flange, compatible with most TPO membranes.

Strainer Dome: 7" (17.78 cm) tall cast aluminum strainer dome that is easy to remove for cleaning.

U-Flow® Mechanical Seal*: Provides a watertight connection to PVC and cast iron pipes.

* Watertight U-Flow® Mechanical Seal requires U-Flow screwdriver, sold separately

Heavy-Duty-TPO-RetroDrain-700X700

Installation Guides

Heavy Duty TPO RetroDrain®

 

Available Documents

One-piece spun aluminum body, heavy-duty cast aluminum dome/clamping ring and depressed sump area.

Designed to replace existing drains in all roofing systems. The onepiece spun aluminum body and heavy-duty cast aluminum dome and clamping ring provide strength and durability. The drain flange has a depressed sump area for improved flow and to facilitate water drainage from roof surface.

One-piece Seamless Body: 0.125" (3 mm) spun aluminum with 12" (30.48 cm) drain stem length, and an extra large 17.5" (44.45 cm) diameter flange that allows positive attachment of roof flashing membrane.

Strainer Dome: Available in two options: 7" (17.78 cm) tall cast aluminum (pictured), or 5.5" (13.97 cm) tall cast aluminum SuperDome with screw down lid, to secure against vandals.

Clamping Ring: The heavy-duty cast-aluminum clamping ring ensures a uniform compression seal of the membrane for strength and durability.

U-Flow® Mechanical Seal*: Provides a watertight connection to PVC and cast iron pipes.

* Watertight U-Flow® Mechanical Seal requires U-Flow screwdriver, sold separately. Hercules® RetroDrain® and U-Flow® are registered trademarks of OMG Roofing Products.

Heavy-Duty-TPO-RetroDrain-700X700
Available Documents

Spun aluminum round drain attachment for use with all RetroDrains.

The OverFlow assembly provides additional water drainage, if necessary, when water level on the roof exceeds 4" (10.16 cm) in height. It is a spun aluminum round drain attachment that is designed to be used with all RetroDrains that are supplied with a clamping ring assembly. Simple and easy to install. The FlowControl assembly provides a specific limited water flow rate under different water pressures (water head) on the roof, and performs as an overflow drain if the water level on the roof exceeds 4" (10.16 cm) in height. It is a spun aluminum round drain attachment with two specially designed weirs, and is compatible with RetroDrains that are supplied with a clamping ring assembly.

Material: Each is a one-piece, 0.050" (1.27 mm) spun aluminum attachment, 4" (10.16 cm) in height.

* OverFlow®, FlowControl®, and RetroDrain® are registered trademarks of OMG Roofing Products

Overflow and FlowControl
Available Documents

Coping system for use with all types of roof systems.

A cost-effective snap-on coping system designed for use with single ply, built-up and modified bitumen roofing systems. The system consists of galvanized steel anchor clips and aluminum or galvanized coping covers in a variety of thicknesses and colors.

Anchor Clips: 12" wide Galvanized steel base with stainless steel spring clip designed to keep upward pressure on the coping cover. Pre-punched for proper fastener location.

Coping Cover: Available in 12 ft (3.7 m) lengths of either aluminum or galvanized steel, lengths and gauges listed below.

Concealed Splice Plate: 8" (20.3 cm) wide plate, with metal and finish to match cover, and dual non-curing isocryl butyl sealant strips to allow for thermal movement and seals joints.

Finishes: Steel and aluminum available in a number of standard Kynar®* 500 colors, aluminum also available in mill and anodized finishes. Custom colors available upon request.

Accessories: Factory-fabricated miters, end caps, and tees are available with “quicklock” or welded seams.

Custom Capabilities: Quicklock and welded radius coping available along with other specially fabricated coping products to meet the needs of the project.

*Kynar® is a registered trademark of Arkema, Inc.

Presto-Lock-Coping-System-700X463
Available Documents

For Single Ply Roofing Systems

Edge One Fascia system offers convenience and economical pricing to simplify projects and maximize profits. Our Edge One Fascia for single-ply roofs helps to protect the roof system against high wind events, saving the building from costly damage. The design eliminates the stripping in typical of other products, making Edge One Fascia fast and easy to install.

Anchor Cleat: 12' (3.7 m) lengths, 20 gauge (1.00 mm) formed galvanized steel, preslotted 12" (30.48 cm) o.c. with 6" (15.24 cm) wide stainless steel spring clips at 48" (1.22m) o.c.

Fasteners: Stainless Steel #10 x 2" (5.08 cm) fasteners with hexagonal head and driver bit are furnished. Masonry fasteners available upon request.

Fascia Cover: Snap-On covers in 12' (3.7 m) lengths, available in 24 ga. (0.6 mm) steel and 0.040" (1.02 mm) aluminum, other metals available upon request. Factory “notched” to provide a 1" (2.54 cm) lap joint.

Finishes: Steel and aluminum available in a number of standard Kynar®* 500 colors, aluminum also available in mill and anodized finishes. Custom colors available upon request.

Accessories: Factory-fabricated corners, overflow and spillout scuppers, downspout sumps, radius and special angles, extenders and soffit clip systems are also available.

*Kynar® is a registered trademark of Arkema, Inc.

Available Documents

A high performance edge treatment for all ballasted single ply roof projects

A high performance edge treatment for all ballasted single ply roof projects. Nonpenetrating design allows for vertical face attachment without penetrating the horizontal flange, and eliminates the need to strip-in the deck flange, eliminating potential delamination between the adhesive and metal deck flange due to thermal expansion and contraction forces. Provides maximum protection against wind uplift damage.

Anchor Bars: 12' (3.7 m) lengths, extruded 6063-T6 alloy aluminum, preslotted 12" (30.48 cm) o.c.

Fasteners: Stainless Steel #9 x 2" (5.08 cm) fasteners with hexagonal head and driver bit are furnished. Masonry fasteners available upon request.

Fascia Cover: Snap-On covers in 12' (3.7 m) lengths, available in 24 ga. (0.6 mm) steel and 0.040" (1.02 mm) aluminum, other metals available upon request. Factory “notched” to provide a 1" (2.54 cm) lap joint.

Anchor Bar Splice Plates: Provided compression gasket allows for thermal movement of the fascia systems.

Finishes: Steel and aluminum available in a number of standard Kynar®* 500 colors, aluminum also available in mill and anodized finishes. Custom colors available upon request.

Accessories: Factory-welded anchor corners, overflow and spillout scuppers, downspout sumps, radius and special angles, extenders and soffit clip systems are also available.

*Kynar® is a registered trademark of Arkema, Inc.

Presto-Tite-Fascia-System-Ballasted-SP-700X514

Installation Guides

Installation Instructions

Available Documents

Non-penetrating edge treatment eliminates the need to strip-in the deck flange.

A high performance edge treatment for all modified bitumen and BUR roof projects. Nonpenetrating design allows for vertical face attachment without penetrating the horizontal flange, and eliminates the need to strip-in the deck flange, eliminating potential delamination between the asphalt and metal deck flange due to thermal expansion and contraction forces. Provides maximum protection against wind uplift damage.

Anchor Bars: 12' (3.7 m) lengths, extruded 6063-T6 alloy aluminum, preslotted 12" (30.48 cm) o.c.

Fasteners: Stainless Steel #9 x 2" (5.08 cm) fasteners with hexagonal head and driver bit are furnished. Masonry fasteners available upon request.

Fascia Cover: Snap-On covers in 12' (3.7 m) lengths, available in 24 ga. (0.6 mm) steel and 0.040" (1.02 mm) aluminum, other metals available upon request. Factory “notched” to provide a 1" (2.54 cm) lap joint.

Anchor Bar Splice Plates: Provided compression gasket allows for thermal movement of the fascia systems.

Finishes: Steel and aluminum available in a number of standard Kynar®* 500 colors, aluminum also available in mill and anodized finishes. Custom colors available upon request.

Accessories: Factory-welded anchor corners, overflow and spillout scuppers, downspout sumps, radius and special angles, extenders and soffit clip systems are also available.

*Kynar® is a registered trademark of Arkema, Inc.

Presto-Tite-Fascia-System-Bituminous-700X515
Available Documents

Non-penetrating edge treatment eliminates the need to strip-in the deck flange.

A high performance edge treatment for fully adhered or mechanically fastened single ply roof projects. Nonpenetrating design allows for vertical face attachment without penetrating the horizontal flange, and eliminates the need to strip-in the deck flange, eliminating potential delamination between the adhesive and metal deck flange due to thermal expansion and contraction forces. Provides maximum protection against wind uplift damage.

Anchor Bars: 12' (3.7 m) lengths, extruded 6063-T6 alloy aluminum, preslotted 12" (30.48 cm) o.c.

Fasteners: Stainless Steel #9 x 2" (5.08 cm) fasteners with hexagonal head and driver bit are furnished. Masonry fasteners available upon request.

Fascia Cover: Snap-On covers in 12' (3.7 m) lengths, available in 24 ga. (0.6 mm) steel and 0.040" (1.02 mm) aluminum, other metals available upon request. Factory “notched” to provide a 1" (2.54 cm) lap joint.

Anchor Bar Splice Plates: Provided compression gasket allows for thermal movement of the fascia systems.

Finishes: Steel and aluminum available in a number of standard Kynar®* 500 colors, aluminum also available in mill and anodized finishes. Custom colors available upon request.

Accessories: Factory-welded anchor corners, overflow and spillout scuppers, downspout sumps, radius and special angles, extenders and soffit clip systems are also available.

*Kynar® is a registered trademark of Arkema, Inc.

Presto-Tite-Fascia-System-SP-700X525

Installation Guides

Installation Instructions

Available Documents

Factory-Fabricated Coated Metal Edge System

Presto-Weld drip edge is a factory-fabricated coated metal edge system used to terminate at the perimeter of a PVC or TPO membrane. This edge comes with a factory applied, 8" wide PVC flashing strip or 6" wide TPO flashing strip of Johns Manville membrane to help save labor installation costs in the field. Presto-Weld is an economical solution for many conditions such as continuous edge drainage with or without a gutter condition.

Anchor Cleat: 12' (3.7 m) lengths, 22 gauge (0.79 mm) formed galvanized steel, preslotted fastener holes at 12" (30.48 cm) o.c.

Fasteners: 1 ¼" (32 mm) ring shank roofing nails, provided.

Fascia Cover: 12' (3.7 m) lengths, available in 24 ga. (0.6 mm) steel PVC or TPO coated with pre-slotted fastener holes at 6" o.c.

Finishes: Standard membrane colors available.

Accessories: Factory-fabricated corners, and special angles and extenders are also available.

Face Height 3" (76.2 mm), 4" (102 mm), 6" (152 mm)

RS-6117_PrestoWeld_Drip_edge
Available Documents

One-piece spun aluminum body, plastisol-coated flange and depressed sump area.

Designed for use in single ply PVC roof systems to replace existing drains in re-roofing applications. This one-piece, spun aluminum body has a plastisol-coated flange for direct hot-air welding of PVC roof membranes. The drain flange has a depressed sump area to facilitate the easy drainage of all water from the roof surface.

One-piece Seamless Body: 0.064" (1.6 mm) spun aluminum body with 12" (30.48 cm) drain stem length, and an extra large 17.5" (44.45 cm) diameter plastisol-coated flange for direct hot-air welding of PVC roof membranes.

Strainer Dome: 7" (17.78 cm) tall, heavy-duty cast aluminum strainer dome is easy to remove for cleaning.

U-Flow® Mechanical Seal*: Provides a watertight connection to PVC and cast iron pipes.

* Watertight U-Flow® Mechanical Seal requires U-Flow screwdriver, sold separately. AlumaWeld® RetroDrain® and U-Flow® are registered trademarks of OMG Roofing Products.

Heavy-Duty-TPO-RetroDrain-700X700
Available Documents

Manufactured with a copolymer resin and incorporating a cast aluminum strainer dome with screw-down lid.

Manufactured with a tough copolymer resin that is compatible with any roofing system, RetroDrains are designed to replace existing drains in re-roofing applications. PC/PET drains can even withstand the heat associated with torch down roofing applications. RetroDrains are designed to be simple and easy to install from the rooftop.

One-Piece Seamless Body: Manufactured from engineered resin of Polycarbonate Polyethylene Terepthalate (PC/PET), with a 12.35" (31.37 cm) length drain stem, and a 13.9" (35.31 cm) diameter flange.

Cast Aluminum SuperDome: A screw down access lid secures the drainage system against vandals.

U-Flow® Mechanical Seal*: Provides a watertight connection to PVC and cast iron pipes.

UV Stable: Provides for long life and reliability.

* Watertight U-Flow® Mechanical Seal requires U-Flow screwdriver, sold separately. SuperDome® and RetroDrain® are registered trademarks of OMG Roofing Products.

SRP_DV_SuperDome_RetroDrain
Available Documents

Extra long screwdriver to tighten the special recessed head screws on U-Flow compression seals.

The U-Flow®* Screwdriver is an accessory product used in the installation of RetroDrain®* products with the U-Flow Seal. Specifically for tightening the special recessed head screws on the U-Flow compression seals. The extra long shaft of the screwdriver ensures ease of reach when tightening the connection screws on all U-Flow retrofit products. The screwdriver comes complete with a loss prevention bar.

Tip: #2 Robertson square tip

Shaft: 12.5" (31.75 cm) shaft length

* RetroDrain® and U-Flow® are registered trademarks of OMG Roofing Products.

UFlow-Screwdriver-700X600
Available Documents

Elastomeric membrane bellows and 4" metal flanges for use with vertical expansion joints.

Expand-O-Gard expansion joints are flexible waterproof closures for vertical building walls designed to accommodate movement between building components caused by thermal, settlement, wind, flex and seismic forces.

Bellows:

Widths: 4" - 12" (10.16 cm - 30.48 cm) Standard

(Special sizes are available up to 54" [1.37 m] wide)

Membrane Covers

EPDM (Style WS)

Thickness: 0.060" (1.52 mm)

Colors: Black or White - premium priced and available upon request.

Neoprene (Style F)

Thickness: 0.060" (1.52 mm)

Color: Black - premium priced and available upon request.

Closed Cell Support Foam

Thickness varies from 0.375" - 0.75" (9.53 mm to 19.1 mm) depending on bellows width.

Flange1 :

Aluminum2 : .032" (0.81 mm)

Copper: 16 oz. (0.56 mm)

Galvanized Steel2 : 26 ga. (0.56 mm)

Stainless Steel: .018" (0.46 mm) folded to .036" (0.91 mm)

1. Other metals are available upon request.

2. Available in Kynar® finish colored upon request. Kynar® is a registered trademark of Arkema, Inc.

Styles:

WS = For masonry construction, metal buildings and panel wall systems where flanges are concealed and/or sandwiched within the wall system.

F = For joints between new and existing vertical walls, between curtain walls and glass atriums, and other vertical building walls where the flange is part of the closure design. Factory fabricated transitions are available.

Vertical-Expansion-Joint-Cover-700X700
Available Documents